- Home
- All Products
- Universal 4" Upholstery Tool for Hoo... Universal 4" Upholstery To...
Model # 304593001
Universal 4" Upholstery Tool for Hoover Carpet Washers
- Universal 4\" upholstery tool for removing tough stains on chairs, sofas and other pieces of furniture
Earn Hoover Points with this purchase
i
HOOVER REWARDS
Sign up with your name, email & birthday details for a custom reward experience. Fuel up your energy bank with points by shopping, liking us on social or even referring others and convert points into spendable rewards or exclusive savings on your favorite products!
Universal 4" Upholstery Tool for Hoover Carpet Washers
$13.99
Item added to cart.
Item could not be added to cart. Quantity selected may exceed available supply.
Read "Before you Begin Cleaning" instructions.
Be sure to check Hoover Cleaning Guide on page
10 and the cleaning code on your upholstery. Use
your cleaner only on upholstery marked "W" or
"W/S".
1. Attach hose and solution tube as instructed.
2. Place handle in upright position. SpinScrub
brushes will not rotate while handle is in upright
position.
3. Fill Clean Water Tank according to instructions
on (Pg. 8).
4. Fill
solution
container
solution according to instructions on (Pg. 8).
Do not use hard floor cleaning solution when
cleaning upholstery.
5. Attach tool to end of hose.
6. Dry hands and plug cleaner into a properly
grounded outlet.
7. Set Wash/Rinse Selector to WASH. Turn
cleaner ON.
8. Gently press the tool onto the fabric. Press the
trigger and slowly pull the nozzle over the
fabric (Fig. 39).
9. Overlap strokes by 1/2 inch to help prevent
streaking.
10. Make additional strokes without pressing the
trigger to remove more solution.
To clean in corners or creases, lift the tool one
half inch from the fabric and press the solution
trigger.
11. For heavily soiled areas, it may be necessary
to repeat the cleaning process. Make
crisscrossing strokes to the original pattern;
overlap each pass (Fig. 40).
Make no more than 2 passes with the solution
over any one area to prevent over-wetting and
damage to fabric.
12. If you would like to rinse the carpet with water
only, set Wash/Rinse Setting switch to RINSE
(Fig. 41). For best cleaning results, Hoover
recommends to rinse the carpet with water
only. This will remove residual carpet cleaning
solution from your carpets. Then set Wash/
Rinse Selector to rinse and repeat steps 7 and 8.
actual model may vary from images shown.
with
HOOVER
®
14
39
40
If additional cleaning is necessary, wait until the
upholstery is completely dry before using the tool
again.
Empty Dirty Water Tank when the motor sound
becomes higher pitched and there is a loss in
suction (see "Automatic Shut-Off").
When finished cleaning, follow "After Cleaning"
and "After Using Tool" instructions.
41
Home - Diy
The Hoover SteamVac Spin Scrub is a carpet cleaner with a one gallon clean water tank, 12 amp motor, heated cleaning, 20-foot-long cord, grip-style handle, 96-inch-long hose and a set of attachments, including an upholstery tool.
The Hoover SteamVac Spin Scrub upholstery tool can be used to clean couches and other furniture.
Attach the tool to the main hose on the vacuum to suction dirt and debris from upholstery surfaces such as couches and chairs. The tool is fairly simple to use and can help keep fabrics and coverings looking clean.
Things You Will Need
+
- Hoover brand cleaner
- Water
Turn off and unplug the Spin Scrub. Push down on the tank handle and pull forward, and set the tank aside. Take the hose out of the storage rack and step on the foot pedal to lower the handle to the floor.
Undo the latch on the back part of the recovery tank and lift off the lid. Slide the front panel off the recovery tank by pulling up on it. Slide the attachment converter into the front of the recovery tank.
Pull the beige collar on the connecting tube toward the tube, which will extend the black tabs. Open the lid on the “Stair/Upholstery Cleaning Connection” hood and push the connector into the hose inside the hood. Push down to connect.
Replace the tank on the Spin Scrub after filling the tank with cleaning solution and water. Set the front edge of the tank lid on the tabs on the front of the tank and then turn the tank lid to close.
Lift up the handle and attach the upholstery tool to the end of the hose by pushing them firmly together until the tool clicks into place.
Turn the Spin Scrub “On” and hold the upholstery tool against the palm of your hand. Wait 15 seconds and squeeze the trigger. Once the cleaning solution dispenses from the tool, set the upholstery tool on the surface to be cleaned and squeeze the trigger again to begin cleaning the fabric.
Move the upholstery tool over the now damp section on the fabric and then pull it back. Release the trigger and move the tool back over the same area. Continue over the fabric to be cleaned until finished, creating overlapping sections.
The Drip Cap
- The Hoover SteamVac Spin Scrub is a carpet cleaner with a one gallon clean water tank, 12 amp motor, heated cleaning, 20-foot-long cord, grip-style handle, 96-inch-long hose and a set of attachments, including an upholstery tool.
- Undo the latch on the back part of the recovery
tank and lift off the lid.
- Slide the front panel off the recovery tank by pulling up on it.
- Wait 15 seconds and squeeze the trigger.
- Once the cleaning solution dispenses from the tool, set the upholstery tool on the surface to be cleaned and squeeze the trigger again to begin cleaning the fabric.
References
Writer Bio
Meredith Jameson writes early childhood parenting and family health articles for various online publications. She holds a Bachelor of Arts in history from San Francisco State University.
Photo Credits
- Jupiterimages/Goodshoot/Getty Images
- Jupiterimages/Goodshoot/Getty Images
More Articles