Emergency ballast for led t8

$9699 $139.99 USD

Sorry, this product is temporarily out of stock, please check Related Products below, or use the email for stock updates

Free Economy Shipping Within The Contiguous U.S.

Description

Emergency battery backup and LED driver for LED T8 and T5 ballast bypass lamps

Features:
- 5 Watt output power
- 1.8 Watt standby power
- 90 minute battery run time at 5W
- Output and over-power protection
- Lithium Ion battery
- 0?C-50?C Operating temperature
- Recharge 24 hours max
- 5 Year warranty

For use with the following lamps:
1. Satco 4' T8 (S9720?S9723)
2. Satco U-Bend (S9930?S9933)
3. Satco 4' T5 LED bypass lamps (S29717?S29719)
4. Satco next generation double ended bypass lamps.

Specs

‎

• 10 watts of emergency power for one lamp
• Constant power over 90 minutes
• Standby power consumption of only 1 watt
• Easy retrofit of existing EM units, similar wiring pattern
• UL listed for use in the USA and Canada
• Compatible with LED Type B direct wire T8 lamps
• Recharges in 24 hours or less
• Works with select T5, T8, and PL-L
• Designed for 100 deep cycle life
• Five Year warranty

• Description
• Specification Downloads

Description

10 watt Constant Power for 90 minutes

TBEM10 is an emergency back-up power source designed to drive LED T8, T5 and PL-L Type B UL tubes in the event of a power failure. The TBEM10 provides a solution when retrofitting existing fixtures which have integral emergency back-up systems. The TBEM10 provides 10 watts of constant power to a single tube for a minimum of 90 minutes, meeting NEC and NFPA requirements for emergency lighting when installed properly. It is an energy saving solution to existing fluorescent emergency systems and installs following a similar wiring diagram, utilizing both switched and un-switched load wires found in these applications. Ships complete with installation instructions and test switch. The charging system and lithium-ion battery have a design life of over 100 deep cycles. 5 year warranty. The TBEM10 is compatible with most EarthTronics 24”, 36”, 48” and U-Bend T8 LED Type B tubes as well as select T5 Type B.

Please consult lamp compatibility list at Emergency Back-Up Type B Compatibility List

Adding an Emergency Ballast kit to your existing light fixture allows the fixture to operate in emergency mode for at least 90 minutes during a power outage. Our emergency ballast kits include an emergency battery, charger and inverter circuit. Use the chart below to find the ballast needed for your installation.

The store will not work correctly in the case when cookies are disabled.

Emergency Ballasts

The commercial electrical contractor's source for emergency ballasts and emergency lighting supplies. Compare and buy T8 linear fluorescent ballasts, T5 emergency ballasts and more for your commercial lighting project or retrofit.

Top Brands

• CREE
• GE Lighting
• Green Creative
• Howard Lighting
• Juno Lighting
• Light Efficient Design
• Lithonia Lighting
• Maxlite
• NaturaLED
• RAB Lighting
• Sylvania
• Wago

Emergency ballasts for T12, T8 and T5 linear fluorescent fixtures continue supplying power to the fluorescent lamps when there is a loss of power to the circuit. Like any linear fluorescent electronic lighting ballast, during normal operation, emergency ballasts limit the voltage or current across the lamps, preventing the lamps or circuits from failing.

Throughout regular operation, a battery built into the ballast maintains a charge. During an outage, the battery in the emergency ballast keeps the fluorescent tubes illuminated for 90 minutes or more. Emergency ballasts are rated to supply a consistent lumen output off the battery power, ranging from 300-500 lumens on the low end all the way up to 3000 lumens on the high end.

Linear fluorescent emergency ballasts are essential for security and life safety in a commercial lighting application. You can select standalone emergency ballasts from our inventory, or choose a complete linear fluorescent emergency ballast retrofit kit for your installation.

Shop By

Shopping Options

Fluorescent Lamp Type

1. Linear Tube 10
2. U-Bend Tube 1

Wattage Range

1. 0 - 5 Watt 1
2. 6 - 10 Watt 5
3. 11 - 15 Watt 1
4. 16 - 20 Watt 3

Mounting Height

1. 8 - 10 Feet 1

Certifications

1. CSA 1
2. CUL Listed 1
3. ETL Listed 3
4. FCC Compliant 3
5. Lighting Facts 1
6. NEC 8
7. NFPA 9
8. OSHA 4
9. ROHS 8
10. Title 24 Compliant 1
11. UL Listed 24
12. show 2 more show less

Technology

1. Emergency Ballast 29
2. Emergency Driver 6
3. LED 1
4. LED - New Fixture 1
5. T8 Fluorescent 1

Lumen Range

1. 0 - 500 5
2. 501 - 1000 4
3. 1001 - 1500 5
4. 2501 - 3000 1

Manufacturer

1. Howard Lighting 7
2. IOTA 2
3. Keystone Technologies 10
4. Litetronics 3
5. Mule Lighting 10
6. NaturaLED 1
7. SLG Lighting 3
8. Universal Lighting Technologies 3

Product Warranty

1. 3 Year 1
2. 5 Year 25

Type of Area

1. Apartment Buildings 1
2. Hangers & Storage 1
3. Home & Architectural 2
4. Industrial & Warehouse 2
5. Office & Small Retail 3
6. Schools 1
7. Hotels 1
8. Maintenance Rooms 1
9. Factory / Industrial 2
10. Hospitality 1
11. Retail 1
12. show 2 more show less

Voltage

1. 120V 1
2. Multivolt 120V-277V 34

Lamp Life

1. 40,001 - 50,000 Hours 1

Number of Lamps

1. 1 Lamp 2
2. 2 Lamp 1
3. 4 Lamp 5

Ballast Start Type

1. Instant Start 39

© 2022 ShineRetrofits.com. All Rights Reserved. Your source for induction lights, LED, and fluorescent fixtures and retrofit kits.

Will a fluorescent emergency ballast work with LED lights?

Can you use a T8 LED bulb without a ballast?

Can I bypass the ballast for LED lights?

Do you need a special ballast for LED lights?