LED ALARM CLOCK MANUAL Show Model: 30037 TO OPERATE THE CLOCK: When plugged in an AC outlet, the display will blink on and off meaning the incorrect time is being displayed. You should always check the time when this is indicated. The clock will automatically displayed AM/PM, but you must be sure to correctly set the indicator for the time and alarm. When the PM indicator is on, "PM" will be displayed and when the AM indicator is on, nothing will be displayed. When the alarm indicator is displayed, then the alarm will sound at the set time. TO SET THE TIME: Slide the TIME SET switch (2) to T. Set. Press and hold the HOUR button (5) to your desired hour. Be careful to set AM/PM correctly. When PM time is set, "PM" will appear on display. Press and hold MINUTE SET button (3) to your desired minute. Slide the TIME SET switch (2) to the lock position. TO SET THE ALARM TIME: Slide the ALARM switch (2) to A. Set. Press and hold the HOUR SET button to your desired hour. Be careful to set AM/PM correctly. When PM time is set, "PM" will appear on display. Press and hold MINUTE SET button (3) to your desired minute. Slide the A. SET switch (2) to the lock position. TO TURN THE ASCEDING ALARM ON/OFF: Slide the ALARM ON/OFF SWITCH (1) to the "ON" position. A bell symbol will be visible on the display when the alarm is activated. The alarm will sound at the selected alarm time. Slide the ALARM ON/OFF SWITCH (1) to the "OFF" position to turn the alarm off. TO USE THE SNOOZE FEATURE: When the alarm is sounding, press the SNOOZE button (4) .The bell symbol will blink on and off indicating the snooze mode is activated. The alarm will sound again after 8 minutes. BATTERY BACKUP: This clock has an optional battery backup feature, designed to retain the time and alarm settings in the event of a power failure. To use the battery backup, insert one 1 .5V "AA" battery into the Battery Compartment (6) noting the correct polarity. Note that the battery can be installed without unplugging the clock. If the power fails, the battery backup will automatically continue running the clock maintaining the time and alarm settings. However, the display will disappear. When the power is restored, the display will reappear. The battery will maintain timekeeping and the alarm setting for approximately 8 hours during the power failure or interruption. If using the battery backup feature, it is recommended to change the battery annually.
Operation: When the clock plugged in, the display will blink on and off meaning the correct time needs to be set. Auto Dimmer: The display brightness is automatically adjusted according to the amount of light in the room. The display brightness will automatically dim when the room darkens. The light sensor is located under the front grill. Setting the Time: 1. Press and hold the Time Button 2. Press the Hour Button until the correct hour is displayed. Remember to set the correct AM/PM (PM indicator will light up for the PM time) 3. Press the Minute Button until the correct minute is displayed 4. Release the Time Button once the time has been set. Setting and Operating the Alarm: 1. Press and hold the Alarm Button 2. Press the Hour Button and then the Minute Button (MIN) to set the desired wake up time. Remember to set the correct AM/PM (PM indicator will light up for the PM time) 3. Release the Alarm Button once the alarm time has been set 4. Slide the Alarm ON/OFF switch to ON to activate the alarm (Alarm Indicator will light up on the display) Super Loud LED Alarm Clock MODEL 30240 OPERATING MANUAL BATTERY INSTALLATION TO SET THE TIME TO SET THE ALARM TIME How do you change the time on an equity alarm clock?SETTING THE TIME. Slide the LOCK/ALARM/DATE/TIME switch (G) to the CALENDAR position and the hour/minute digits will begin to flash.. Press the HOUR/MONTH button (E) to set the hour. ... . Press the MINUTE/'DATE button (D) to set the minute.. How do you set time on equity Insta clock?OWNER'S MANUAL. Press and hold DST/SET Button for 5 - 7 seconds. ... . Use the (+) (−) Buttons to set the year.. Press the DST/SET Button again for month & date.. Use the (+) (−) Buttons to set the month & date.. Press the DST/SET Button again for hours (rember AM PM).. Use the (+) (−) Buttons to set the hour.. How do you set equity quartz alarm clock?To set alarm (on models with alarm) Turn the alarm setting knob to the desired time in the direction of arrow and push up alarm switch on side of case. On models with alarm switch on back of clock, please slide the alarm switch to ON position. To turn the alarm OFF, slide switch to OFF position.
|