How to use hoover carpet cleaner upholstery attachment

Read "Before you Begin Cleaning" instructions.

Be sure to check Hoover Cleaning Guide on page

10 and the cleaning code on your upholstery. Use

your cleaner only on upholstery marked "W" or

"W/S".

1. Attach hose and solution tube as instructed.

2. Place handle in upright position. SpinScrub

brushes will not rotate while handle is in upright

position.

3. Fill Clean Water Tank according to instructions

on (Pg. 8).

4. Fill

solution

container

solution according to instructions on (Pg. 8).

Do not use hard floor cleaning solution when

cleaning upholstery.

5. Attach tool to end of hose.

6. Dry hands and plug cleaner into a properly

grounded outlet.

7. Set Wash/Rinse Selector to WASH. Turn

cleaner ON.

8. Gently press the tool onto the fabric. Press the

trigger and slowly pull the nozzle over the

fabric (Fig. 39).

9. Overlap strokes by 1/2 inch to help prevent

streaking.

10. Make additional strokes without pressing the

trigger to remove more solution.

To clean in corners or creases, lift the tool one

half inch from the fabric and press the solution

trigger.

11. For heavily soiled areas, it may be necessary

to repeat the cleaning process. Make

crisscrossing strokes to the original pattern;

overlap each pass (Fig. 40).

Make no more than 2 passes with the solution

over any one area to prevent over-wetting and

damage to fabric.

12. If you would like to rinse the carpet with water

only, set Wash/Rinse Setting switch to RINSE

(Fig. 41). For best cleaning results, Hoover

recommends to rinse the carpet with water

only. This will remove residual carpet cleaning

solution from your carpets. Then set Wash/

Rinse Selector to rinse and repeat steps 7 and 8.

actual model may vary from images shown.

with

HOOVER

®

14

39

40

If additional cleaning is necessary, wait until the

upholstery is completely dry before using the tool

again.

Empty Dirty Water Tank when the motor sound

becomes higher pitched and there is a loss in

suction (see "Automatic Shut-Off").

When finished cleaning, follow "After Cleaning"

and "After Using Tool" instructions.

41

Home - Diy

The Hoover SteamVac Spin Scrub is a carpet cleaner with a one gallon clean water tank, 12 amp motor, heated cleaning, 20-foot-long cord, grip-style handle, 96-inch-long hose and a set of attachments, including an upholstery tool.

The Hoover SteamVac Spin Scrub upholstery tool can be used to clean couches and other furniture.

Attach the tool to the main hose on the vacuum to suction dirt and debris from upholstery surfaces such as couches and chairs. The tool is fairly simple to use and can help keep fabrics and coverings looking clean.

Things You Will Need

+

• Hoover brand cleaner
• Water

1. Turn off and unplug the Spin Scrub. Push down on the tank handle and pull forward, and set the tank aside. Take the hose out of the storage rack and step on the foot pedal to lower the handle to the floor.

2. Undo the latch on the back part of the recovery tank and lift off the lid. Slide the front panel off the recovery tank by pulling up on it. Slide the attachment converter into the front of the recovery tank.

3. Pull the beige collar on the connecting tube toward the tube, which will extend the black tabs. Open the lid on the “Stair/Upholstery Cleaning Connection” hood and push the connector into the hose inside the hood. Push down to connect.

4. Replace the tank on the Spin Scrub after filling the tank with cleaning solution and water. Set the front edge of the tank lid on the tabs on the front of the tank and then turn the tank lid to close.

5. Lift up the handle and attach the upholstery tool to the end of the hose by pushing them firmly together until the tool clicks into place.

6. Turn the Spin Scrub “On” and hold the upholstery tool against the palm of your hand. Wait 15 seconds and squeeze the trigger. Once the cleaning solution dispenses from the tool, set the upholstery tool on the surface to be cleaned and squeeze the trigger again to begin cleaning the fabric.

7. Move the upholstery tool over the now damp section on the fabric and then pull it back. Release the trigger and move the tool back over the same area. Continue over the fabric to be cleaned until finished, creating overlapping sections.

The Drip Cap

• The Hoover SteamVac Spin Scrub is a carpet cleaner with a one gallon clean water tank, 12 amp motor, heated cleaning, 20-foot-long cord, grip-style handle, 96-inch-long hose and a set of attachments, including an upholstery tool.
  
• Undo the latch on the back part of the recovery tank and lift off the lid.
  
• Slide the front panel off the recovery tank by pulling up on it.
  
• Wait 15 seconds and squeeze the trigger.
  
• Once the cleaning solution dispenses from the tool, set the upholstery tool on the surface to be cleaned and squeeze the trigger again to begin cleaning the fabric.

References

Writer Bio

Meredith Jameson writes early childhood parenting and family health articles for various online publications. She holds a Bachelor of Arts in history from San Francisco State University.

Photo Credits

• Jupiterimages/Goodshoot/Getty Images
• Jupiterimages/Goodshoot/Getty Images

More Articles

Can you use Hoover carpet cleaner on couch?