Iphone 12 pro max back screen repair

All prices are in Singapore dollars and include GST. Pricing and terms might vary at Apple Store and other service providers.

iPhone screen repair pricing

Screen repair pricing applies if:

• The screen needs to be replaced due to accidental damage or mishandling. Accidental damage isn’t covered by Apple warranty.
• The screen gets broken while your iPhone is still under warranty and you don’t have AppleCare+ coverage.
• The screen stops working and your iPhone isn’t covered by Apple warranty, consumer law, or AppleCare+.

If your iPhone has additional damage that’s not limited to the screen, see “Replacement” fees. If your original iPhone was severely damaged by accident or abuse, service might not be available.

iPhone Model

Screen Repair

Replacement

If we need to replace your iPhone, your replacement iPhone will be equivalent to new in performance and reliability.

Screen repair and accidental damage fees with AppleCare+

AppleCare+ includes two incidents of accidental damage coverage. You can use an incident for screen repair/back glass* or other damage to your iPhone. Each incident has a service fee. The following prices are for Apple repairs with AppleCare+ accidental damage coverage.

iPhone Model

Screen Repair or Back Glass*(AppleCare+)

Replacement(AppleCare+)

* Back glass: iPhone 12, iPhone 13 or iPhone 14 models only

Battery service

Dependent on Apple diagnostics test result, your iPhone battery service might be covered by warranty, AppleCare+, or consumer law. Otherwise, you’ll pay an out-of-warranty fee for battery service.

iPhone Model

In-warranty or with AppleCare+

Out-of-warranty

Other services

Your iPhone might need other repairs, such as the Home button, the rear camera, or liquid damage. You might be able to use an incident of AppleCare+ accidental damage coverage for these repairs.

Not all issues are repairable. If your iPhone has catastrophic damage or is inoperable after unauthorised modifications, you might need to buy a replacement. A diagnostic fee of S$ 130 may apply if upon inspection, we ascertain that unauthorised modifications have been made to an iPhone.

Your iPhone service might be covered by warranty, AppleCare+, or consumer law. We’ll inspect your product to determine the final service fee.

If your iPhone 12 Pro Max screen is cracked, not responding to touch, or not showing a picture when your phone is powered on, use this guide to restore your iPhone to working order with a new screen, a.k.a. display assembly. This guide only covers steps for replacing a full display assembly that comes with a shield plate preinstalled.

The combined earpiece speaker + sensor assembly affixed to the back of the display is paired to your individual iPhone from the factory, so you must transfer it from your old display to your new one during any display replacement. It contains the flood illuminator, which is part of the biometric Face ID security feature. If it is damaged or replaced, Face ID will cease to function, so take extra care not to damage any of these components during this procedure. If damaged, only Apple or an Apple-authorized technician can restore Face ID function.

Note: True Tone functionality is disabled after a screen replacement, even when using an original Apple screen.

• Caution: Before you begin, discharge your iPhone battery below 25%. A charged lithium-ion battery can catch fire and/or explode if accidentally punctured.

• Power off your iPhone before beginning disassembly.

• Remove the two 6.7 mm-long pentalobe P2 screws at the bottom edge of the iPhone.

• Opening the iPhone's display will compromise its waterproof seals. Have replacement seals ready before you proceed past this step, or take care to avoid liquid exposure if you reassemble your iPhone without replacing the seals.

• If your iPhone has a cracked screen, keep further breakage contained and prevent bodily harm during your repair by taping over the glass.

• Lay overlapping strips of packing tape over the iPhone's display until the whole face is covered.

• This will keep glass shards contained and provide structural integrity when prying and lifting the display.

• Wear safety glasses to protect your eyes from any glass shaken free during the repair.

• If the broken glass makes it difficult to get a suction cup to stick in the next few steps, try folding a strong piece of tape (such as duct tape) into a handle and lifting the display with that instead.



• Remove four 1.1 mm-long Y000 screws securing the battery and display connector cover.

• Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from to avoid damaging your iPhone.

• During reassembly, this is a good point to power on your iPhone and test all functions before you seal the display in place. Be sure to power your iPhone back down completely before you continue working.

• Remove the battery and display connector cover.

• Use a spudger or a clean fingernail to pry the battery connector up from its socket on the logic board.

• Try not to damage the black silicone seal surrounding this and other board connections. These seals provide extra protection against water and dust intrusion.

• Bend the connector slightly away from the logic board to prevent it from accidentally making contact with the socket and providing power to the phone during your repair.

• Use a spudger or a fingernail to disconnect the display cable connector.

• To re-attach press connectors like this one, carefully align and press down on one side until it clicks into place, then repeat on the other side. Do not press down on the middle. If the connector is misaligned, the pins can bend, causing permanent damage.

• Use a Y000 driver to remove the four 1.1 mm-long screws securing the front sensor connector cover.

• Swing the cover up from the left until the small clip on the right unhooks.

• Remove the cover.

• During reassembly, insert the clip on the right edge into its slot first, then hinge the rest of the cover into place.

• Use a spudger or a fingernail to disconnect the front sensor assembly cable connector.

• Remove the four screws securing the speaker/sensor assembly to the back of the display.

• Two 1.3 mm Phillips screws

• One 1.8 mm shouldered Y000 screw

• One 1.1 mm Y000 screw

• The earpiece speaker is lightly adhered in place.

• Use tweezers or the point of a spudger to gently pry up the top edge of the speaker.

• Flip the speaker assembly over—down and away from the top edge of the display.

• The speaker remains attached via a very thin ribbon cable. Be careful not to strain or damage the cable.

• Prepare an iOpener and apply it to the top front of the display for 1-2 minutes, in order to soften the adhesive securing the sensors.

• A hair dryer, heat gun, or hot plate may also be used, but be careful not to overheat the display.

• Use the point of a spudger to lift the proximity sensor and flood illuminator module out of its notch in the front panel.

  How much does it cost to repair iPhone 12 Max back glass?

  Apple iPhone 12 Pro Max Back Glass Replacement $199. Low-cost cracked iPhone 12 Pro Max back glass replacement. Takes about 90 minutes. Parts + labor & lifetime guarantee.

  How much does it cost to replace back of iPhone 12 Pro Max?

  If you don't have AppleCare+, get ready to dig your hands deep into your pockets and pay the out-of-warranty price. Here's how much it costs to have your iPhone 12's back glass replaced: iPhone 12 Pro Max: $499. iPhone 12 Pro: $449.